Power Steering using Toyota MR2 EHPS pump DIY Electric Car Forums

11 Июн 2014 | Author: | Комментарии к записи Power Steering using Toyota MR2 EHPS pump DIY Electric Car Forums отключены
Toyota Avalon Electric Cars

Power Steering using Toyota MR2 EHPS pump

Many EV conversions have to deal with Power Steering decision. If you decided to keep PS and looking how to drive PS pump, consider this all-in-one solution brought to you by Toyota engineers. Toyota MR2 has EHPS ( Electric Hydraulic Power Steering ) in which pump is driven by its own electric motor instead of pulley hanging off the main engine like most ICE cars do.


First generation of MR2 had separate fluid tank, motor/pump assembly and controller, some EVers took motor/pump and wired it directly to 12V or via various switching circuits designed to keep the pump off while driving straight or at high speed to save power.

However, 3rd generation of MR2 also called Spyder has a single pump assembly combining motor, pump, fluid tank and controller, making it very attractive option for EV community.

To the best of my knowledge you are looking for 2000-2005 ( maybe some other years, I’m not sure ) EHPS pump from Toyota MR2 Spyder, call your local junk yards or check this one online http://car-part.com. The pump looks like this:

To wire it use schematics below. If you don’t have proper harnesses you can either solder directly or create your own connectors for each pin. I personally created connectors and then filled harnesses with caulk to keep wires in place.

It can be removed later if needed.

Although 50 Amp relay is stated, I couldn’t find one so I used typical 40 Amp automotive relay, my testing shows that it doesn’t actually reach 50 Amp current anyway.

You can wire VSS signal from your car to make the pump turn itself off at higher speeds, but I couldn’t manage that because my Miata has unusual VSS signal. Even without VSS, the pump runs idle at 4 Amps until you actually turn the steering wheel, so the power wasted is very minimal.

You’d have to find a way to connect PS Pressure line from the pump to your car’s rack and return line from the rack back to the pump. Return line is easy, just use 3/8 hose and clamps. As for pressure line, if you are lucky you can fit one from other Toyota models, if not, you can make custom one from separately purchased fittings and the pressure hose, I have seen those on Ebay and online shops like this one http://www.summitracing.com/

Hope this helps, feel free to update this Wiki with more details, my main goal was to publish schematics and wiring, I am not very good with hydraulics, maybe someone can add details on making custom pressure hose.

Toyota Avalon Electric Cars

Here are the Toyota part#’s for the electrical Connectors: These part#’s get the Plastic part only, The metal pin wiring parts are sold separately. Maybe someone can add the part#’s for those.

Part#’s Large connector 90980-12068

Middle connector 90980-10897

Small end connector 90980-10942

There are two part numbers for the wiring. They come with the plugs, rubber seals, about 6 inches of wire. At $6.55/ea they aren’t cheap for what you get, but they are made to fit.

Three pigtails for the small middle connectors P/N: 82998-12440

Two pigtails for the large connector P/N: 82998-12500

Toyota Avalon Electric Cars
Toyota Avalon Electric Cars
Toyota Avalon Electric Cars
Toyota Avalon Electric Cars
Toyota Avalon Electric Cars
Toyota Avalon Electric Cars
Toyota Avalon Electric Cars
Toyota Avalon Electric Cars
Toyota Avalon Electric Cars

Interesting articles

Other articles of the category "Toyota":

Twitter-news
Our partners
Follow us
Contact us
Our contacts

dima911@gmail.com

423360519

About this site

For all questions about advertising, please contact listed on the site.


Catalog ALL Electric Cars and hybrid/ News and Information about Electric Car and Electric Vehicle Technologies, batteries for vehicle catalog with specifications, pictures, ratings, reviews and discusssions about Electric and Hybrid cars - Green energy